Product Description
1/4 HP Russell Watergardens RW-2800 Pump - 3180 gph
The RW-2800 Pond and Waterfall Pump is a reliable and dependable submersible pump.
The RW Series Pond and Waterfall Pumps are the most reliable submersible pumps for ponds and waterfalls. Each RW submersible pump is designed and built to be truly continuous operators. This provides you with the confidence to operate your pond and/or waterfall 24/7/365. The RW Series submersible pumps are constructed of Stainless Steel and corrosion resistant polyamide Fiber Reinforced Resin.
Quiet operation and large water flow makes the RW-2800 a great choice for pondless waterfalls and all types of ponds.
- The RW-2800 pump creates beautiful waterfalls up to 18" wide over natural stone. At 1,800 gallons per hour, the RW-2800 pump is perfect for backyard waterfalls and streams.
- The RW-2800 pump fits inside most pond skimmers, but is ideally suited for the Seagull and Piper HydroClean™ Pond Skimmers.
- The RW-2800 pump fits inside most pondless pump vaults but is ideally suited for the HydroChamber™ as part of an Ultimate Pondless System.
- Use a RW-2800 pump as a replacement for failed Aquascape, Little Giant, Savio, Easy Pro, Tsurumi, Beckett, Cal Pump, and many other brands of submersible pumps.
- High-Volume Direct Drive Submersible Pump
- Removable fish guard for solids handling capability
Features:
- Heavy-duty motor designed for continuous duty operation
- Non corrosive construction
- 304 stainless steel and polyamide fiber reinforced resin for corrosion resistance
- Air filled motor for lower average operating temperature
- Seamless stainless steel stator casing
- Seal extender for cooling the seal face more effectively
- Double Silicone Carbide mechanical seals SIC/CE/CA
- Thermal overload protection
- Fiber reinforced impeller
- Leak resistant cable entry
- Air release valve preventing air lock
- Anti-vibration bearing technology
- Stainless steel motor housing for superior heat dissipation
- Stainless steel shaft
- Fiber reinforced vortex impeller
- Reinforced resin volute
- Stainless steel hardware
- Lightweight and energy efficient
- Approved: CSA/C-US
Specifications:
- 3,180 max gph
- 2,800 gph @ 5′ head
- 2″ female threaded outlet
- 1/4 horsepower
- 23′ max head
- 120 volt, 3.5 amps
- 420 input watts
- 20′ heavy duty power cord with grounded plug
- $24.19 monthly operating cost @ $0.08 per kilowatt hour
- 1 year warranty
- Dimensions: Length 9.25", Width 6.1", Height 13.9",
- Weight: 12.76 lbs.
Use with CVA-200 Custom Cam Lock Check Valve Assembly for HydroClean Pond Skimmers and HydroChamber Pump Vault
RW-2800 Pond Pump Flow Rate GPH @ Head
| RW-2800 | 0' | 5' | 10' | 15' | 20' |
| GPH | 3,180 | 2,800 | 1,950 | 1,080 | 180 |
Electrical
- Pump must be protected by a ground fault circuit interrupter (GFCI).
- Pump must be plugged into a standard, properly grounded, three pronged outlet. Pump MUST NOT BE HARDWIRED.
- Do not cut or alter the electrical cable.
- Never move or handle the pump by pulling on the electrical cable. Make sure the electrical cable does not become excessively bent or twisted, does not rub against a structure in a way that might damage it, and does not come in contact with heated surfaces.
- Upon receipt of pump - examine the cable for damage from shipping. If damaged, contact us immediately for a replacement. DO NOT INSTALL a pump with a damaged electrical cable!
- Cutting or altering electrical cable in any way VOIDS the warranty. Installing a pump with a damaged cable VOIDS the warranty.
- Operation
- Do NOT run pump dry.
- Pay careful attention to the water level while the pump is operating. Dry operation may cause the pump to malfunction. Pump must always operate while fully submersed. Pump failure due to dry operation VOIDS the warranty.
